| Number of inputs and outputs |
Number of digital outputs: 2; Number of analogue outputs: 1 |
| Measuring range |
|
| Measuring range [MPa] |
0...60 |
| Process connection |
homogeniser connection |
| Special feature |
Gold-plated contacts |
| Measuring element |
diaphragm seal |
| Application |
flush mountable for the food and beverage industry |
| Media |
liquids and gases |
| Medium temperature [°C] |
5...90; (for further details see section Diagrams and graphs) |
| Min. bursting pressure |
|
| Min. bursting pressure [MPa] |
100 |
| Pressure rating |
|
| Pressure rating [Mpa] |
80 |
| Note on pressure rating |
| take into account the pressure resistance of the screws and seals used |
|
| Vacuum resistance [mbar] |
-1000 |
| Type of pressure |
relative pressure |
| Operating voltage [V] |
18...30 DC; (to SELV/PELV) |
| Current consumption [mA] |
< 35 |
| Min. insulation resistance [MΩ] |
100; (500 V DC) |
| Protection class |
III |
| Reverse polarity protection |
yes |
| Power-on delay time [s] |
0.3 |
| Integrated watchdog |
yes |
| Number of inputs and outputs |
Number of digital outputs: 2; Number of analogue outputs: 1 |
| Total number of outputs |
2 |
| Output signal |
switching signal; analogue signal; IO-Link; (configurable) |
| Electrical design |
PNP/NPN |
| Number of digital outputs |
2 |
| Output function |
normally open / normally closed; (parameterisable) |
| Max. voltage drop switching output DC [V] |
2 |
| Permanent current rating of switching output DC [mA] |
250 |
| Switching frequency DC [Hz] |
< 500 |
| Number of analogue outputs |
1 |
| Analogue current output [mA] |
4...20; (scalable 1:5) |
| Max. load [Ω] |
500 |
| Analogue voltage output [V] |
0...10; (scalable 1:5) |
| Min. load resistance [Ω] |
2000 |
| Short-circuit protection |
yes |
| Type of short-circuit protection |
pulsed |
| Overload protection |
yes |
| Measuring range |
|
| Measuring range [MPa] |
0...60 |
| Analogue start point |
|
| Analogue start point [MPa] |
0...48 |
| Analogue end point |
| 120...600 bar | 1740...8700 psi |
|
| Analogue end point [MPa] |
12...60 |
| Set point SP |
| 4...600 bar | 60...8700 psi |
|
| Set point SP [MPa] |
0.4...60 |
| Reset point rP |
| 1...597 bar | 20...8660 psi |
|
| Reset point rP [MPa] |
0.1...59.7 |
| Min. difference between SP and rP |
|
| Min. difference between SP and rP [MPa] |
0.3 |
| In steps of |
|
| In steps of [MPa] |
0.1 |
| Set point SP |
| 4...600 bar | 55...8702 psi |
|
| Set point SP [MPa] |
0...60 |
| Reset point rP |
| 1...597 bar | 19...8666 psi |
|
| Reset point rP [MPa] |
0...60 |
| Min. difference between SP and rP |
|
| Min. difference between SP and rP [MPa] |
1 |
| In steps of |
|
| In steps of [MPa] |
1 |
| Switch point accuracy [% of the span] |
< ± 0,4; (Turn down 1:1) |
| Repeatability [% of the span] |
< ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1) |
| Characteristics deviation [% of the span] |
< ± 1; (linearity incl. hysteresis and repeatability, limit value setting to DIN EN IEC 62828-1) |
| Hysteresis deviation [% of the span] |
< ± 0,1; (Turn down 1:1) |
| Long-term stability [% of the span] |
< ± 0,05; (Turn down 1:1; per 6 months) |
| Temperature coefficient zero point [% of the span / 10 K] |
0,2; (5...80 °C) |
| Temperature coefficient span [% of the span / 10 K] |
0,2; (5...80 °C) |
| Response time [ms] |
< 1.5 |
| Delay time programmable dS, dr [s] |
0...50 |
| Damping process value dAP [s] |
0...4 |
| Damping for the analogue output dAA [s] |
0...4 |
| Max. response time analogue output [ms] |
3 |
| Parameter setting options |
hysteresis / window; normally open / normally closed; switch-on/switch-off delay; Damping; Display unit; current/voltage output |
| Communication interface |
IO-Link |
| Transmission type |
COM2 (38,4 kBaud) |
| IO-Link revision |
1.1 |
| SDCI standard |
IEC 61131-9 |
| SIO mode |
yes |
| Required master port type |
A; (when pin 2 not connected: B) |
| Supported DeviceIDs |
| Type of operation | DeviceID |
|---|
| Factory setting / CMPT = 2 | 458 | | Status_B High Resolution / CMPT = 3 | 637 |
|
| Note |
| For further information please see the IODD PDF file under "Downloads" |
|
| Profiles |
Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis |
| Min. process cycle time [ms] |
2.3 |
| IO-Link resolution pressure [bar] |
0.1 |
| IO-Link process data (cyclical) |
| function | bit length |
|---|
| pressure | 14 | | binary switching information | 2 |
|
| IO-Link functions (acyclical) |
application specific tag |
| Profiles |
Smart Sensor ED2: Digital Measuring Sensor (0x000A), Identification and Diagnosis (0x4000) |
| Min. process cycle time [ms] |
3 |
| IO-Link resolution pressure [bar] |
0.2 |
| IO-Link process data (cyclical) |
| function | bit length |
|---|
| pressure | 16 | | device status | 4 | | binary switching information | 2 |
|
| IO-Link functions (acyclical) |
application specific tag |
| Ambient temperature [°C] |
5...80 |
| Storage temperature [°C] |
-40...100 |
| Protection |
IP 67 |
| EMC |
| DIN EN 61000-6-2 | | | DIN EN 61000-6-3 | |
|
| Shock resistance |
| DIN EN 60068-2-27 | 50 g (11 ms) |
|
| Vibration resistance |
| DIN EN 60068-2-6 | 10 g (10...2000 Hz) |
|
| MTTF [years] |
146 |
| Weight [g] |
1444.2 |
| Materials |
1.4542 (17-4 PH / 630); stainless steel (1.4404 / 316L); stainless steel (1.4435 / 316L); PBT+PC-GF30; PBT-GF20; PC |
| Materials (wetted parts) |
stainless steel (1.4435 / 316L) |
| Min. pressure cycles |
60 million |
| Process connection |
homogeniser connection |
| Display |
| Display unit | 3 x LED, green (bar, psi, MPa) | | switching status | 2 x LED, yellow | | measured values | alphanumeric display, red/green 4-digit |
|
| Pack quantity |
1 pcs. |
| Connection |
Connector: 1 x M12; coding: A; Contacts: gold-plated |
